PRODUCT NAME: PRECISION LIQUID WOOD FILLER HMIS CODES: H F R P
PRODUCT CODE: LWF-100, LWF-500 2 3 0 G
SECTION I - MANUFACTURER IDENTIFICATION
MANUFACTURER'S NAME: Precision Technology LLC
ADDRESS: 4052 Getwell Road
Memphis, TN 38118
EMERGENCY PHONE: 800-424-9300 DATE PRINTED: November 15, 2003
INFORMATION PHONE: 901-363-0526 NAME OF PREPARER: Precision Technology LLC
SECTION II - HAZARDOUS INGREDIENTS / SARA III INFORMATION
OCCUPATIONAL EXPOSURE VAPOR PRESSURE
__________________________________________________________________________________________
* Indicates toxic chemical(s) subject to the reporting requirements of Section 313 of Title III and of 40 CFR 372.
SECTION III - PHYSICAL / CHEMICAL CHARACTERISTICS
BOILING RANGE: 132oF- 232oF SPECIFIC GRAVITY (H2O=1): 0.87
VAPOR DENSITY: Heavier than air EVAPORATION RATE: Slower than Ether
COATING V.O.C.: MAX 5.51 lb/gL (660g/L) MATERIAL V.O.C.:
SOLUBILITY IN WATER: No
APPEARANCE AND ODOR: Liquid, typical odor of solvent(s) above
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: 1oF METHOD USED: Closed Cup
FLAMMABLE LIMITS IN AIR BY VOLUME - LOWER: 1.2 UPPER: 12.8
EXTINGUISHING MEDIA: Foam, alcohol foam, CO2, dry chemical, water fog.
SPECIAL FIREFIGHTING PROCEDURES: water spray may be ineffective. Water spray may be used to cool closed containers to prevent pressure build-up and possible rupture of containers. Water fog is preferred. Fire fighters should wear self contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Extremely flammable liquid and vapor! Vapors may cause flash fire. Keep away from heat, sparks, and flame. Do not smoke. Extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Closed containers may explode when exposed to extreme heat.
SECTION V – REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: None
INCOMPATIBILITY (MATERIALS TO AVOID):
Avoid contact with strong alkalies, strong mineral acids or strong oxidizing agents.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS:
Dry material exposed to high heat such as welding or flame-cutting operations may release carbon monoxide.
HAZARDOUS POLYMERIZATION
Will not occur.
SECTION VI – HEALTH HAZARD DATA
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Effects from vapors or spray mists in poorly ventilated areas may include irritation of the mucus membranes. Inhalation of vapors or spray mists may also result in nausea, dizziness, breathing difficulty, headaches, and loss of coordination.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Eye Contact: Causes severe eye irritation. Symptoms include redness, tearing, burning, and visual disturbances
Skin Contact: May cause skin irritation or sensitivity. Symptoms include redness, cracks, swelling, and dermatitis.
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
May be harmful if absorbed through the skin. Symptoms include nausea, headache, irritation, swelling, and redness of affected areas.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Harmful or fatal if swallowed. Symptoms include gastrointestinal irritation, nausea, vomiting, and diarrhea.
HEALTH HAZARDS (ACUTE AND CHRONIC)
Inhalation-(ACUTE): May cause dizziness, breathing difficulty, headaches & loss of coordination.
(CHRONIC): Repeated exposure to high vapor concentration may cause irritation of the respiratory system and permanent brain and nervous system damage. Eye-contact- Severe irritation, tearing, redness, and blurred vision. Skin contact- Can dry and de-fat skin causing cracks, irritation, and dermatitis. Ingestion- Can cause gastrointestinal irritation, vomiting, and diarrhea.
CARCINOGENICITY
NTP CARCINOGEN: No IARC MONOGRAPHS: No OSHA REGULATED: Yes
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Unknown
EMERGENCY AND FIRST AID
Inhalation:
Do not induce vomiting. Can cause chemical pneumonitis and pulmonary edema if material is aspirated into the lungs. Call physician or emergency response agency immediately.
Eye contact:
Flush eyes with large amounts of water for at least 15 minutes. Seek medical attention.
Skin contact:
Flush with water followed by washing with soap and water.
Ingestion:
Remove victim to fresh air. Apply artificial respiration and other supportive measures as required. Seek medical attention.
SECTION VII – PRECAUTIONS FOR SAFE HANDLING AND USE
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE
Keep containers closed when not in use. Do not store above 120oF. Store large quantities only in buildings designed and protected to comply with OSHA 1910.106. Keep out of reach of children. Vapors of this product may travel long distances during use. Take adequate precautions to prevent potential explosive ignition of these vapors.
OTHER PRECAUTIONS
Since containers of this material may contain residues(vapor, liquid, or solid) when “empty” , all hazard precautions given in this data sheet must be observed. Read and understand safety precautions before using this product. Keep closure tight and container upright to prevent leakage. Avoid breathing sanding dust. Intentional misuse by deliberately concentrating and inhaling this product can be harmful or fatal.
SECTION VIII – CONTROL MEASURES
RESPIRATORY PROTECTION
Overexposure to vapors may be prevented by using ventilation controls, vapor exhaust or fresh air entry. NIOSH/MSHA approved (TC-23C) paint spray or air supplied (TC-19C) respirators may also reduce exposure. Read respirator manufacturer’s instructions carefully to determine the type of airborne contaminants which the respirator is effective
VENTILATION
Provide sufficient mechanical ventilation to keep the concentration of ingredients listed in section2 below the lowest suggested exposure limits.
PROTECTIVE GLOVES
Gloves should be constructed of nitrite, neoprene, or latex, or impervious to the ingredients listed in Section 2.
EYE PROTECTION
Use chemical safety glasses, goggles or face shields for protection.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
To prevent repeated or prolonged skin contact, wear gloves, clothing, and footwear, which are designed for protection when using this material.
WORK / HYGIENIC PRACTICES
Wash thoroughly after handling. If clothing or footwear is contaminated, discard or launder.
WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.
SECTION IX – SPILLAGE OR LEAK PROCEDURE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Dike and contain spill with inert material (sand, earth, etc.). Transfer liquid to containers for recovery or disposal. Do not allow spilled material to enter drains or sewer systems. Remove all sources of ignition. Provide maximum ventilation. Do not allow personnel to enter spill area if they are not using proper protective gear as outlined in Section 8.
WASTE DISPOSAL METHOD
Dispose of waste in strict accordance with all local, state, and federal regulations.
SECTION X – DISCLAIMER
Data relates only to the specific product described and not to such product in combinations with any other product and no agent for Precision Technology LLC is authorized to vary any such data. Precision Technology LLC and its agents disclaim all liability for any actions taken of forgone reliance upon such data.